Overall Rating:

4 / 5

Good home shop press,

March 23, 2009

By Magoomike

from Mason, TX

"This press is suitable for working on autos or small tractors. It provides enough strength to separate corroded parts when used with a penetrating solvent and works well to replace bearings and seals."

What is your level of technical expertise? Home Handyman

Share this Review:

Overall Rating:

5 / 5

good for bike work,

March 15, 2009

By crebo

from texas

Reviewer Images

(click to see full-size image)

"bought this press for bike work, specifically to press the stem out of a harley lower triple tree, worked great, press rod is the exact size to fit in the triple tree hole. install instructions suck, but just look at the assembled pic and you will figure it out. I tightened all the bolts after its was all together and it sets flush with the garage floor. will have many uses on a bike and 12 ton was more than enough to press out the stem... overall I was impressed for the money..."

What is your level of technical expertise? Home Handyman

Share this Review:

Overall Rating:

5 / 5

12 ton hydraulic Press,

November 18, 2008

By Rip1972

from Sartell, MN

"bought the press on sale, needed it for some motorcycle repair. Worked great for the money, small enough to fit under shelving."

What is your level of technical expertise? Professional

Share this Review:

Overall Rating:

3 / 5

worth the money,

April 23, 2008

By matt08

from Iowa

"Press was easy to assemble, and works very well for small tasks. My only complaint is that the ram floats around too much for precise bearing, or gear onto shaft assemby."

What is your level of technical expertise? Professional

Share this Review:

Overall Rating:

5 / 5

shop press,

April 21, 2008

By c1492

from San Antonio, TX

"I bought this press to replace U-joints on farm and construction equipment. I works great. I am sure it has other uses which I will find. It is small enough to move around easily; however, I will probably install casters on the base to make it very portable within my shop. I would recommend this product to anyone needing a small press for U-joint work or similar applications."

What is your level of technical expertise? Professional

Share this Review:

Overall Rating:

4 / 5

Good press for home garage.,

April 21, 2008

By NateSC

from South Carolina

"used this press for doing some wheel bearings on my car. Press costs less than the shop wanted just to use theirs. Works well, have also used it to bend some brakets and other uses. I would definatly recomend this press for a home mechanic."

What is your level of technical expertise? Home Handyman

Share this Review:

Overall Rating:

5 / 5

12 ton hydralic press,

April 14, 2008

By kk25

from barrington, il

"the press was easy to put together. it is also, very easy to use. press comes with necessary hardware to be properly used (blocks)."

What is your level of technical expertise? Home Handyman

Share this Review:

Overall Rating:

4 / 5

Nice little press,

January 21, 2008

By JayCee

from Romulus, MI

"This is a nice little press that packs a lot of punch. Easy to assemble/disassemble. I had to re-drill out the holes that the adjustable pins run through, but this wasn't a big deal. It's a good value for a home/garage mechanic. Has enough power for most automotive press needs. Comes with a set of press plates. Press punches would have been nice."

What is your level of technical expertise? Home Handyman

Share this Review:

Overall Rating:

4 / 5

Good home shop press,

January 21, 2008

By AndyMan

from Nashville, TN

"Setup and function of this press are slow. Design is so-so, but quality is great. For a homeowner that needs a press this size from time to time, this is an excellent buy."

What is your level of technical expertise? Home Handyman

Share this Review: